how to fix phone charger port

Phone stand with charger port

thingiverse

This stand is for smart phones it features a charger port for a phones charger cable. this does need supports its printed at z:154 y:131 x:80 it will take 12 hours and 45 minutes to print unless the speed is incressed. how fun printing. if you...

Tesla Model 3 Qi Charger phone fix

thingiverse

A quick fix for a Qi-charger for the Tesla model 3, it prevent the phone from slipping out of the charging pad. ... Like this one for exemple:...

Tutorial: How to fix Over-defined Sketch in SolidWorks?

grabcad

... with sketcher. ... here is quick fix tutorial on How to solve the over defined sketch in S/W. ...================================================== Tutorial Here: http://grabcad.com/questions/tutorial-how-to-solve-over-defined-sketch-in-solidworks

how to fix printing in the center of bed.

thingiverse

I made this simple mark to measure the offset of my nuzzle from the bed center after that need to update the marlin firmware with X_MIN_POS and Y_MIN_POS ( to move the nuzzle toward the x limit sensor need to add the diffrent between the center of...

How to?

grabcad

How to fix a bullet to a key ring without drilling a hole (an destroying it in the process) Use a circlip (internal dia 10mm)

Flush to the wall phone charger holder

thingiverse

I created a holder for the old Motorola 'square' charger that supports the phone, holding it against the wall. One design hold the phone above the outlet. The other holds the phone below the outlet. ... My phone is in a case, so it is a little larger...

Camper 12v to USB charger box (phone charger)

thingiverse

I found a 2 plug 12v usb plug with a built in voltage meter on amazon (https://www.amazon.com/gp/product/B01M0GR0FQ/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1) and i added a hole for a 12v push button switch since the voltage readout would always...

How to fix a chair in 20 min using a Makerbot

thingiverse

... You can probably figure out how to measure and design your own bolt if needed. Design bolt Skeinforge it taking account the extreme thin tower for the bolt (possibly lower temp or activate cool or towering) Print ??? ...Screw in chair Profit!

Phone Charger

grabcad

Phone charger with two USB charging ports.

S4 Case with Speaker port to front of the phone

thingiverse

After my first test print, I will be considering adding additional space to insert small strips of foam pad to further surround and insulate the speaker port from vibrations. Instructions See...

iphone charger sup[port

thingiverse

Fix your broken charger

Charger Port Protector

thingiverse

TPU Cap for charger port on my son's Jetson Hoverboard to keep out dirt, debris, and splashes. ... Not Guaranteeing water tight - But better than exposed open port.

PHONE CHARGER

grabcad

PHONE CHARGER

Phone-charger

cults3d

Phone-charger

Phone Charger

grabcad

Phone Charger

grabcad

Phone Charger

grabcad

Phone Charger

Droid Charger Port

thingiverse

I know some people prefer a 12V outlet, but for my droid, I got tired of removing the head every time I wanted to access the battery to charge it for lights and such, so I whipped this up to hold a Battery Tender Junior charger connection. ...The...

8 Port USB Charger

thingiverse

This is a simply 8 port USB Charger that uses a buck converter to provide 5 Volt power for the USB ports. I have a video on YouTube Showing this project in a little more detail. ... Video: https://www.youtube.com/watch?v=umFoTEZVV-I USB ports used:...

phone charger

grabcad

this phone charger is a simple example to practice the part design of CATIA

Phone Charger

grabcad

A single part of a Phone Charger

phone charger

grabcad

it is a two pin phone charger

Hoverboard charger port cover

thingiverse

Bought one of these chinese two wheel hoverboards, missed a way to protect the charging port from dust and moisture. Made this plug in Tinkercad. Printed in PLA on my machine its too loose, i just wrapped some scotchtape around for a snug fit. ...Print...

MagSafe 2 Charger fix

thingiverse

How to open your power supply in one minute : youtube.com/watch?v=HjKeqfVUm-o Another one to fix cables (I did it my own way without replacing original cable inside the block) : youtube.com/watch?v=G1HYBqeWSHI Add a protection case to your charger...

Phone Charger

thingiverse

Designed a phone charger holder for your phone. ...Designed to hold 98mm round wireless charger with cable hole routed. Sits in stock organizer in a 2017 F250. Would upscale it 101% to let charger fit w/o sanding and cable holder as well.

Phone-charger

grabcad

Phone-charger RenderingModel by "Alex Gavaz" Gavaz Alex

HOW_TO_COOK ReMix

thingiverse

Reworked Seafax's stl to incorporate magnet options, I usually go with 10mm X 2mm rounds (4 spots for them), but also included two spots for 20mm rounds. Print it with supports and only pull out the spots you plan on using (it's on the back, who's...

How To Print Glass

thingiverse

How to print GLASS! The first thing to understand is a very slow speed is necessary, so patience is a must. The key is to follow these four steps: 1. 20mm/s speed 2. 0.1000mm layer height 3. No top or bottom layers, along with one single...

Phone Charger

grabcad

In my original design, I also had small walls on the sides of the phone slot, but found that this made it way too difficult to insert the phone into the slot quickly. My design was made at Bergen County Academies under Mr. DeFalco. ...It is designed to...

How to shell tutorial.

grabcad

i want to submit both tutorials as seperite entries but they also need to be looked at and scored as one entry because I believe that if I'm going to make a tutorial then I'm going to do it right and have the full tutorial. ...Please take this into...